Motortopia: Where your passion parks

Motortopia: Where your passion parks.

Why Join Motortopia? Connect with other enthusiasts... Chat! Add Friends! Challenge! Private Message!

  1. cars
  2. bikes
  3. boats
  4. planes

Cars > fcar’s Garage > Blog > 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

 

fcar’s Profile Photo

fcar

M
Shenzhen, Guangdong
China

 
 

Blog Categories

  • fcar’s Garage
    • 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

How To Select Engine Diagnostic System For Domestic And All Over The World Vehicles

By fcar

Filed under: 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

Solution: As there are various models and brands in china, engine electronic control systems can be domestic independently developed, or from joint ventures, import. Because the difference of the brands and the technology capabilities of each vehicle manufacturers, domestic vehicle engine management system can be divided into combined electronic control system, Delphi electronic control system, Marelli electronic control system, SIMENS electronic control system, MOTOROLA, BOSCH etc.. Just Delphi's electronic control system has not less than 10 species. The wrong choice of the system will cause auto fault diagnostic computer unable to communicate with the control unit, false fault, inaccurate fault code inaccurate data stream, misplaced data stream display, etc. problem. Diagnosing the vehicle assembled with such electronic control system should pay attention to the following questions:
1) Vehicle model match with auto fault diagnostic software.
2) The control unit type match with diagnostic software.
3) The control unit model match with diagnostic software.
4) Diagnostic seat match with fault diagnostic connector.
Note: when diagnose the vehicle models that not for sure about the above conditions, only by entering into the system successively and observing the accuracy of data streams to judge whether choose the right electronic control system, or pull out the corresponding sensor actuator, checking whether the fault code of the vehicle fault decoder associated with the pulled out components, to judge whether the system is the right choice

F3-W is the universal Original Gasoline Car Diagnostic Tool, testing the global mainstream petrol vehicles, reaching to the same effect with the OEM diagnostic scanners. Built-in high and low speed CAN-BUS, One Diagnostic Connector can test all the CAN-BUS vehicles. Support almost all OBD-II protocols.

Fcar car code reader can test the vehicles including:

[Europe/ America Cars]
Benz, Ford, GM, BMW, Rover, Volvo, Opel , SAAB, Saab, MG, Peugeot, Porsche, VW, Audi, Citroen, Skoda, , Renault, Fiat;

[Japan and Korea]
Mitsubishi, Toyota, Nissan, Isuzu, Lexus, Honda, Subaru, Mazda, Hyundai, KIA, Daewoo, Ssangyong;

[Chinese Cars]
Shanghai Volkswagen, Shanghai gm, faw Volkswagen, faw pentium, tianjin faw, dongfeng Citroen, guangzhou Honda, guangzhou Toyota, zhengzhou nissan, red flag, byd, jianghuai, brilliance, geely, chery, roewe, cheetahs, hafei, the Great Wall, lifan, zhongtai, changan, changhe, jiangling, youth
Fcar Auto malfunction diagnosis Most Brands are supported
Fcar auto diagnostic equipment Application Systems
Engine, ABS, Transmission, Gasbag, Body Electronic equipment, Smart Key System, Anti-theft System, Power Steering, Cruise System, Instrument System, Gateway, Air-Conditioning System, Sound System, Light System ....

Public Data line is used for communication with ECU information communication with F3-D truck diagnostic scanner

By fcar

Filed under: 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

Public data line is used for connection to F3-D truck scanner, Data line is used for communication with ECU as well as information communication with other vehicle electronic devices, such as electronic instrument panel and other devices. Some engines have two public data lines: one is in the whole wiring harness (engine side data line); another is separated from ECU harness, normally locate in cab.

Pic.4-33 shows the data lines of early electronically controlled engine. They all have a rectangular 12-pin connector. There are 3 kinds of special harness that used for different type of diagnostic data connector, when troubleshooting, maintenance technician connect appropriate diagnostic plug to diagnostic data connector, and then can download fault code saved in ECU memory. New type of electronically controlled engines all adopt standard SAE data line as shown in Pic.4-34?b?.The connection of 6-pin connector is as below, when detect communication failure between pin and truck diagnostic tool, you can measure voltage of this pin with digimer.

?a?. Used for connection with engine, vehicle diagnostic socket and Fcar F3-D truck diagnostic tool,
6-pin socket and 9-pin socket.

?b?.Standard SAE 6-pin German-made connector
A——data line???;voltage normally between 2.5?5V.
B——data line?—?;voltage normally between 0?2.5V.
C——Battery?12V or 24V?;12V Electric System are different from 24V Electric System, normally between 10?27V.
D——open circuit?voltage normally between 4?5V
E——Cylinder body ground?0V
F——Unused.

F3-D heavy truck diagnostic scanner can diagnose all kinds of diesel control systems quickly and easily, especially available for China, Europe, America, Japan and Korea and so on,build-in high/low speed CAN-Bus to satisfy all Can-Bus vehicles;

Coverage: MAN, Mitsubishi Fuso, Scania, ISUZU, MACK, HINO, VOLOV, DAF, Astra, Detroit, BENZ, NISSAN UD, Catepillar, Renault,...and most of CHINA Heavy duty trucks , BUS.........

Bosch, Cummins, Catepillar, Denso, Siemens, Motorola, Zexel, VITO, NanYue, Delphi, Wabco……
http://www.fc...avy-duty.html

Public Data line is used for communication with ECU information communication with F3-D truck diagnostic scanner

By fcar

Filed under: 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

Public data line is used for connection to F3-D truck scanner, Data line is used for communication with ECU as well as information communication with other vehicle electronic devices, such as electronic instrument panel and other devices. Some engines have two public data lines: one is in the whole wiring harness (engine side data line); another is separated from ECU harness, normally locate in cab.

Pic.4-33 shows the data lines of early electronically controlled engine. They all have a rectangular 12-pin connector. There are 3 kinds of special harness that used for different type of diagnostic data connector, when troubleshooting, maintenance technician connect appropriate diagnostic plug to diagnostic data connector, and then can download fault code saved in ECU memory. New type of electronically controlled engines all adopt standard SAE data line as shown in Pic.4-34?b?.The connection of 6-pin connector is as below, when detect communication failure between pin and truck diagnostic tool, you can measure voltage of this pin with digimer.

?a?. Used for connection with engine, vehicle diagnostic socket and Fcar F3-D truck diagnostic tool,
6-pin socket and 9-pin socket.

?b?.Standard SAE 6-pin German-made connector
A——data line???;voltage normally between 2.5?5V.
B——data line?—?;voltage normally between 0?2.5V.
C——Battery?12V or 24V?;12V Electric System are different from 24V Electric System, normally between 10?27V.
D——open circuit?voltage normally between 4?5V
E——Cylinder body ground?0V
F——Unused.

F3-D heavy truck diagnostic scanner can diagnose all kinds of diesel control systems quickly and easily, especially available for China, Europe, America, Japan and Korea and so on,build-in high/low speed CAN-Bus to satisfy all Can-Bus vehicles;

Coverage: MAN, Mitsubishi Fuso, Scania, ISUZU, MACK, HINO, VOLOV, DAF, Astra, Detroit, BENZ, NISSAN UD, Catepillar, Renault,...and most of CHINA Heavy duty trucks , BUS.........

Bosch, Cummins, Catepillar, Denso, Siemens, Motorola, Zexel, VITO, NanYue, Delphi, Wabco……
http://www.fc...avy-duty.html

Benz ME2 engine and ADS automatic damping system controller code menu

By fcar

Filed under: 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

Benz ME2 engine controller code menu
After entry to ME2 engine, [url=http://WWW.Fcar.COM ]Fcar.COM [/url]car diagnostic code reader will display menu, select “controller code” to enter submenu. Read and execute code.

Select the first item of submenu: “Read and execute code”,F3-W or F3-G vehicle diagnostic scanner first read code unit No., code, chassis No., and prompt whether to transfer code to new control model. If select “No”, then back to previous menu. If select ”Yes”,then prompt to close ignition switch, next display replace old control module with new control module and prompt to open ignition switch. Fcar car diagnostic code reader shows read vehicle computer information. Transfer the above data and prompt whether to carry out identification.

After confirm, Fcar car diagnostic code reader judge this control module whether interlocked or not. If interlocked, then prompt “failure to identify, vehicle engine control unit has been locked!”, and return to main menu. Otherwise prompt to input chassis No.

Entry to control unit locking after finished, Fcar car diagnostic code reader prompt “Important! After starting engine for 40 times, engine control unit will be automatically locked! Times of engine starts”, next prompt to start engine, and shows engine speed about 1 minute. Thereafter prompt ” this control module whether match with vehicle? Whether start to be locked”

After confirm, prompt warning information: “Warning! cannot change once control module installed on vehicle! whether start to interlock?”, finished locking prompt ”cannot change after control module interlocked ”.At this moment, special attention to input of chassis No. in the whole process and cannot go wrong.

Benz ADS automatic damping system controller code menu
This full automatic electronic system can issue four kinds of different damping command to each wheel according to different situation. Moreover, it can control the number of spring vibrations under certain conditions, making steering stability not affected, vehicle can start smoothly.

After entry to system, “controller code” in display menu of F3-W car diagnosis tool, display submenu.

Program for specified customers
Select the first item in menu:” Program for specified customers”.F3-W auto scanner tool first read original program, and provide two different options for user: Customer type and standard type. Choose proper type according to actual needs.
Horizontal adjustment: Front axle/rear axle
Select the second item in menu: “Horizontal adjustment front axle/rear axle”. This function is for adjusting front axle horizontal valve and rear axle horizontal valve.

After entry to this menu, F3-W auto diagnosis tool first shows front axle horizontal value, rear axle horizontal value and fault code condition. Meanwhile, user can adjust height of front axle and rear axle; after adjustment, then come to the next step, display front and rear axle height, and prompt whether to save this value.

After user confirmed this value, F3-W car diagnosis tool will send this value to ECU, and matching over.

Power source and testing cable how to connect fcar F3-G Multilingual intelligent diagnosis scanner

By fcar

Filed under: 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

WWW.FCAR.com F3 series auto diagnostic scanners power supply has four kinds of ways,(take F3-G auto diagnostic scanners example)
. Power supply by power adapter
. Power supply by main testing cable, connector and vehicle diagnostic socket
. Power supply by connection of cigarette lighter with vehicle
. Power supply by connection of battery terminal line with vehicle battery

Cable Connection Method
Option of power:
If the diagnostic socket not with power supply,
Can choose ? ? ? in 3.1.1 one of these three
power connection methods to provide power for car diagnostic scanners.
If the diagnostic socket with power, you do not need to connect another power cord.
The connection of testing cable as shown
The prerequisites for vehicle?
1 Confirm the diagnostic socket location, shape, and whether need for external power supply.
2 Select the appropriate connector base on vehicle model and shape of diagnostic socket.
3 Connect one end of the main testing line to the other end of main unit diagnostic connector.
4 Plug diagnostic connector that connected with the main testing line into the vehicle diagnostic socket.
5 Confirm that main unit with power and start up.
Remark: Diagnostic interface in Fig.3.1.2 is standard OBD-II interface, when connecting, 2 ends of main testing cable are required to separately connect with OBD-II connector and Fcar auto diagnostic scanners, plug OBD-II connector into vehicle diagnostic socket to finish connection.

VW Throttle Matching: Take Santana 3000 to illustrate matching process of Basic setting method and steps

By fcar

Filed under: 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

VW Throttle Matching: www.fcar.com
Instruction: Throttle adjustment matching applies to VW vehicles with electronic throttle and without electronic throttle engine system.
Santana GLi not in matching range.
1) Basic setting content: when turn on ignition switch; you can carry out adaptive of throttle control unit and engine control unit
2) In the following cases, adaptive must be performed?
?Power supply interruption
?Dismounting throttle control unit
? ?Replace throttle control unit
? ?Replace engine
? ?Replace engine control unit
3?Conditions for Basic setting
?? No fault in fault memory
?? 11.5V Battery voltage no less than 11.5V
?? Close all accessories
?Throttle should be in idle position
?Engine coolant temperature greater than 85 ?
4?Basic setting method and steps
? Turn on ignition switch and not start engine.(Take Santana 3000 as an example to illustrate matching process)
?Connect F3-D scanner (use OBD-II connector), select and click VW Audi, the screen will display as below:
Pls select Version
V7.2
V7.0
? Click V7.2(note: high version of software fully compatible to low version of software, if software version not high enough, pls upgrade timely),the screen shows as below
Pls select version
V7.2
V7.0
Openning. . .

? After open V7.2,the screen shows as below?
VW Audi diagnostic system
VW Audi diagnostic system

? Click VW Audi system, the screen will show as below?
VW Audi diagnostic system
General system
Power system
Chassis
Comfort system
Electronic system
Function scanning
Address code direct access
? Click General system, the screen will show as below?
General system
01- Engine
02- Automatic transmission
03- ABS
08- Air conditioning
09- Central electric control system
15- Airbag
16- Electronic steering wheel
17- Combination instrument panel (anti-theft)
18- Additional/auxiliary heating system
19- Gateway
22- 4-wheel drive
? Click 01-engine,then screen will show as below?
Audi KWP system function
01- Read vehicle computer model
Read DTC
Clear DTC
03- Component control test
Read Data Stream
04- Basic setting
07- Controller coding
10- Adjust
11- Login
Adaptive value clear
? First read engine DTC, after confirming no DTC, click 04-basic setting and the screen will show as below?



?After enter Channel No.060 in input box, click Confirm then screen shown below(Note: Item 4 shows Adaptive running means throttle and engine computer are matching, when it finished, it will shows Adaptive finished)



After matching finished, press Back button to logout and then turn off ignition switch. Then turn on ignition switch and start engine to verify the matching effect.
? If prompt error in the process of matching, mainly because of the following several reasons?
??Channel No. input error, pls see the last content of this book to choose the appropriate channel No..
?This vehicle without this function: If match SANTANA Gli, this vehicle originally cannot be matched with scanner
??Throttle control unit or wire damage
??Engine at running state, pls flameout, turn on ignition swtich
??Throttle not reach idle stop(Carbon deposit or throttle cable adjustment improper)
??Battery voltage too low;
??Throttle control unit or wire damage;
??Throttle stuck;
??Starting engine or step on accelerator pedal during adaptive.
?A? After matching interruption, fault”17967”or “17973”will be saved in fault memory. Next time when turn on ignition switch, it will automatically perform basic setting.
For Example: Throttle basic setting of Jetta CiX(duel valve)
A? ACommon VW throttle matching channel No.
001
Small Red Flag 488,Passat B4,Audi?100,200,V6 etc. old models?
098
Santana Gsi ,Passat B5?1.8?,Jetta?5 valve?,Audi?A6,V6?
060
Jetta CiX?2 valve?, A6?1.8,1.8T,2.4,2.8?,Passat B5?1.8T,2.8?,BORA, POLO
Notes: After cleaning, adjusting and replacing throttle body; to realize kickdown function of automatic transmission, you need to perform engine computer matching as well as automatic transmission matching; Matching method as below:
Connect to Fcar F3
1. Connect with Fcar
2. Turn on ignition switch, select “02 automatic transmission”
3. Read and clear DTC, and ensure no DTC saved in control unit;
4. Don’t touch engine accelerator pedal;
5. Select"04 basic setting"
6. Input channel No. "000" to confirm;
7. Step on accelerator pedal to floor and keep 3 seconds;
8. Logout, and release accelerator pedal.
Note: For some new VW/Audi vehicles, the channel cannot be used when enter into automatic transmission control system. Here must perform adjustment setting in "01-engine control system ", its channel No. is"063".
Adaptive of throttle and automatic transmission computer is maily the above 2 methods.

First,to understand the relationship between the node jumper box and select the vehicle type diagnosis

By fcar

Filed under: 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

1#?K line? 2#?K line?
3#?K line? GND?Ground wire?negative??
6#?CAN?H?
7#?RSR232+, J1708+, K line?8#?K line?
9#?K line? 10#?K line?
11#?K line? 12#?K line?
13#?K line? 14#?CAN?L?
15#?RSR232?, K line, J1708?, L line
VCC: power line?Positive?? POWER?Power indicator.
Remark: If lack of vehicle electrical equipment knowledge or unable to confirm electrical equipment power supply, please don’t operate jumper, for error operation of jumper may lead to malfunction of electrical failure or FCAR F3-D main unit and wire.

(Auto diagnostic socket related information reconfirmed as below)
? Digital high impedance multimeter (can not use Analog Multimeter)
? When ignition switch to ON Gear, there is supply voltage of vehicle on diagnostic socket. Voltage difference between voltage on diagnostic socket and vehicle battery side can not be above 2.5V.
In diagnosis, if the signal line used is single-line communication (K line), voltage on signal line lower than battery voltage,(if vehicle supply voltage is 12V,then voltage on signal line is 11V, + 0.25V;if 24V,signal voltage is 21V,+ 0.25V)
If double signal line adopts CAN communication, 2 diagnostic lines use multimeter to measure ground wire voltage under the condition that ignition switch open, the sum of both voltages is 5V,average 2.5V,the one voltage little higher than 2.5V is CAN-H, the one voltage lower than 2.5V is CAN-L.
??After understanding of the above, then you can use auto scanner to read DTC. Now make a brief introduction of operation steps for FCAR scanner to read DTC: Confirm diagnostic socket connect properly and then turn on power switch of scanner, and select Diagnostic menu
??
11?Select vehicle type to be diagnosed?
?Diesel
?Machine
??Select vehicle type and then enter into vehicle series or engine select menu (as shown in 4?40):Then enter into engine type or electronically controlled system menu
After entry to engine type or electronically controlled system menu, it will shows function menu of scanner

If need to clear DTC saved in ECU memory, then must select “Clear DTC” menu option. At present, all Electronic Control Systems are required to use this method. Some first generation of Electronic Control System can clear saved DTCs by way of using scanner or dismantling ECU power fuse for 10s and then install. The shortcoming of this kind of system is all DTCs appeared and recorded in the process of driving will disappear once driver cleared DTCs, therefore maintenance technician and fleet maintenance manager would know nothing about the problem of engine and vehicles.

Note: Before clearing DTC, better write down DTCs, also can use printing function of Fcar scanner.
www.fcar.com

Take the mostly commonly used K line communication make a detailed description of connection method steps

By fcar

Filed under: 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

Connection method of K line communication diagnostic socket
??
1?Connection method of CAN line communication diagnostic socket
K line signal voltage is 1V or so lower than battery voltage, Eg, if battery 12V, then signal voltage is about 11V, battery 24V; if battery 24V, then signal voltage is about 23V. When actually measure voltage of pin on vehicle diagnostic socket, there might be deviation of ±0.25V.

Connection method for K line communication with diagnostic socket and Fcar jumper box as shown in picture: signal wire connect to No.7 hole, power line(battery voltage) connect to VCC hole, ground wire connect to GND.

CAN line communication adopts double line of communication, under the condition that ignition switch on, to measure voltage of 2 diagnostic wire with multimeter,
The sum of voltage for the two is 5v, CAN-H line voltage is 2.5?0.25V, CAN-L line voltage is 2.5?0.25V,actually there might be deviation of ±0.25V or so.


Connection method for K line communication with diagnostic socket and Fcar jumper box as shown in picture
CAN-H connect to No.6 hole, CAN-L connect to No.14 hole, power line(battery voltage)connect to VCC hole, ground wire connect to GND.

Note: When actually measure voltage of pin on vehicle diagnostic socket, there might be deviation of ±0.25V.

Connect jumper box with main testing cable, and lock fastening bolts, as shown in left picture.
15 jumper connection holes with numbers marked beside will be seen on jumper box, the corresponding numbers to these connection holes is node relation of standard OBD-II port.

Base on diagnostic socket information of vehicle, connect diagnostic interface of jumper box.

??After connection, turn on ignition switch to ON, at this time power indicator light on jumper box shall be on. Press switch of F3-D main unit,F3-D main unit work properly, appropriate system can be selected for diagnosis.

Note: If lack of knowledge about vehicle electrical equipment or cannot confirm power supply to electrical equipment, please don’t perform jumper operation, for error jumper operation will lead to vehicle electrical equipment or Fcar main unit and cable malfunction.


Vehicle diagnostic equipment socket related information confirm and tools?
?1??Digital high impedance multimeter(must use high impedance multimeter, otherwise will cause damage to computer board)
?2??When ignition switch to ON, diagnostic socket has supply voltage from vehicle, the voltage difference between voltage on diagnostic socket and that of vehicle battery end cannot be above 2.5V.
?3??If signal line used in diagnosis is signal wire communication (K line),voltage on signal line is 1V lower than battery voltage(if vehicle supply voltage is 12V,then voltage of signal wire is 11V±0.25V; if 24V supply, voltage of signal line is23V±0.25V?.
?4??If the communication of duel signal line adopts CAN communication, under the condition that two diagnostic lines in ignition switch on, to measure voltage of ground wire. The sum voltage is 5V, CAN-H line voltage is 2.5V?0.25V?CAN-L line voltage is 2.5V?0.25V, actually there may have deviation of ±0.25V or so.

Universal channel switching circuit and The Overall Structure of Fcar Auto Diagnostic Scanner

By fcar

Filed under: 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

In actual use, different vehicles can use the same diagnostic connector, such as OBD II, but pin of diagnosis signal might be
distributed in different pins. In order to be compatible with different pins, output connector DB15 internal connection channel switching
matrix of auto diagnostic scanner can realize arbitrary switching of 2-way 13 channels through channel switching matrix..

Fcar automotive fault diagnostic scanner adopts dual ARM chip architecture, and lower computer using 32-bit signal processing chip ARM7, running speed up to 60MIPS. The upper computer adopts high-speed 32-bit ARM920T chips, running speed maximum to 200MHZ, can quickly and effectively process data from ECU. Fcar automotive diagnostic tool adopts high-capacity SD card as storage media for program and data, which facilitates data saving and program upgrade, but also easy to exchange data between vehicle diagnostic equipment and PC. In addition, the application of touch screen in the diagnostic scanner also greatly facilitates the users to operate the scanner.

2014 Super Performance 100% Original Fcar-F3-D Scanner For Heavy Duty Scanner Update Online

By fcar

Filed under: 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

F3-D can diagnose all kinds of diesel control systems quickly and easily, especially available for China, Europe, America, Japan and Korea and so on,build-in high/low speed CAN-Bus to satisfy all Can-Bus vehicles.It provides multi-language platform to meet different customers’ demands. Products with integrated structural design, to achieve 12V, 24V power supply automatically changeover.
http://www.fc...avy-duty.html

FCAR F3-W Petrol Diagnostic Scanner For Vehicles Worldwide

By fcar

Filed under: 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

Fcar F3-W petrol diagnostic scanner adopts the advanced modularized design technology for petrol vehicles worldwild.

Fcar F3-W follows the international standard design and adopts the advanced modularized design technology. It can diagnosis all kinds of petrol control systems quickly and easily, especially available for China, Europe, America, Japan, Malaysia and Korea and so on. It provides multi-language platform to meet different customers’ demands. Its wide touch color screen, exquisite look, integrated structural design, single-track working and operation model with super touching screen, these special designs make you feel cozy and freely.

Fcar F3-W petrol diagnostic scanner adopts the advanced modularized design technology for petrol vehicles worldwild Product function
Testing the global mainstream gasoline and 12V diesel vehicles, reaching to the same effect with the OEM scanners. Built-in high and low speed CAN-BUS,one diagnostic connector can test all the CAN-BUS vehicles. Support almost all OBD-II protocols.
http://www.fc...rld-cars.html
Download Drive Magazine Now!

Advertisements

    Special Offers & Deals

Advertisement

 

Cars > fcar’s Garage > Blog > 2014 Original for Gasoline and Diesel with English and Russian (Multi-Functional Professional Newest Version Fcar auto diagnosti)

Print your passion at Motortopia.com (http://www.motortopia.com)