San Antonio, Texas
1964 Chevrolet C-10
1964 Ford F-250
Head to Head
I got this truck from a freind who died of Cancer. We worked hard on this truck untill he got to sick to do anything. Then I continued the work for him. He was verry proud of it before he died. I try to keep it up, and keep it like I know he would want it.
I bought this black beauty from a lady I worked with. She only wanted $500 and I drove home. The engine is still basically Ford 292 Y-Block but now has all forged internals. Check "Specs" for more details of the build-up!
The bed is '67 Ranger, grille is '63 F-350, and the seat is now something I picked up from an '85 F-150. Eileen is currently going under the knife again and now sports a whole slew of goodies under the hood. The 292 is no more and has been modified to a 309 with forged rods, forged crank, and forged Probe dome pistons. Why all the new forged parts? Well, for the new 300 hp Zex fogger plate system, of course! I was lucky enough to get in touch with John Mummert (aka "the Y-Block Guru") and found a TON of aftermarket speed parts offered for the old Y-Block engines. With any luck, you'll see the pics in the next week or so but the only real changes you're going to see are under the hood. This is my parts hauler, after all, and will be kept as my sleeper truck. With all the work, I'm hoping for an honest 700 rwhp when dyno day comes soon.
No AC, no radio, no 4-way flashers, no reverse lights, no fancy wipers, no power steering, and the heat is compliments of the headers running just beneath my feet. Security system? Well, I do have a "Folsom State Prison" sticker in the back window so not too many people are ballsy enough to violate her. Who could ask for more from a truck?
Specs for “Smokie”
283 w/327 crank, R/V cam, punched 40 over, 4brl carb, 3spd std, 4:11 gears possi.
Specs for “Eileen”
1957 truck 292 Y-Block bored to 309 cubic inches
Probe Forged dome pistons (3.86 bore)
Forged FoMoCo 3.30 stroke crankshaft
Forged FoMoCo connecting rods
1964 Ford truck cylinder heads:
P&P, 3-angle valve job,
1.54:1 ratio adjustable rocker arms,
Stainless Ferrea 2.02" intake/1.625" exhaust valves
Cam: Clay Smith Y-292S mechanical flat tappet; 292dur/.485lift
Isky Solid lifters (ISK-302-H)
Cloyes HD double-roller timing set (CLO-C-3031)
Sealed Power high volume oil pump
ARP fasteners throughout
Blue Thunder aluminum 4bbl intake manifold
Zex Nitrous 300 horsepower fogger
Additional fuel for the nitrous system comes via an eleven-gallon fuel cell (Speedway Motors) and a Holley "Red" electric fuel pump. The nitrous bottle is carefully camouflaged by a rickety wooden box bolted down inside the bed so I can maintain the "sleeper" image.
Holley 600 cfm mech. secondary carburetor
Hedman ceramic coated headers
Ignition: ALL MSD including a Pro-Billet distributor, 6-AL ignition box, Blaster 3 coil, and wiring
Exhaust: ALL 2.5" with Flowmaster Super 44 mufflers and dumps
1959 Ford Fairlane 3-speed manual tranny w/jockey shifter
Centerforce Stage III Dual-Friction 11" Paddle Clutch
Dana 60 w/ 3.54 gears, factory 16-spline axles, and a Detroit Locker posi unit
Factory Options for “Smokie”
Factory Options for “Eileen”
Um.....It's got a seatbelt but that's MINE!!!
Eileen did have a factory optioned Tulsa PTO winch I sold it to finance other parts she needed more urgently.
Mods for “Smokie”
Quite a few! Lots on the motor, Running boards, Tool box, CB, Dual antenas, dual exhaust, tinted windows, Bull dog on hood, Yep that's right, a MAC Bull dog hood ornament. My freind wanted it on their so that's where it stays.
Mods for “Eileen”
I "modified" all the factory RUST HOLES with fiberglass and a fresh coat of suede black!
Iron plate (1" thick) rear bumper
Iron plate (1/2" thick) front PTO winch bumper
Whelen Police 200watt PA/Siren....just to annoy my neighbors and move the IDIOTS driving too slowly in the fast lane here in San Antonio!
dambsmooth has no Car photo albums.
Photo Albums 1 – 1 of 1
Vote This challenge has ended!
|Points for Smokie||Total Votes||Points for Eileen|