Motortopia: Where your passion parks

Motortopia: Where your passion parks.

Why Join Motortopia? So you can keep up with events... RSVP! Post Event Photos! Submit Events!

  1. cars
  2. bikes
  3. boats
  4. planes

Cars > Challenges > “Tazmanian Devil” Vs “The Rumbler”

 

MonzterRacing’s Profile Photo

MonzterRacing

M–46
Lincoln, Nebraska
United States

MilitaryTuners’s Profile Photo

MilitaryTuners

M–41
Las Vegas, Nevada
United States

 

1976 Chevrolet Monza Spyder Hatchback

“Tazmanian Devil”

1996 Ford Mustang GT

“The Rumbler”

 
Photo of: 1976 Chevrolet Monza
Photo of: 1996 Ford Mustang
 

Head to Head

 

About “Tazmanian Devil”

This was my third Monza I have owned and it has stayed with me for many years. I bought it off the land my aunt owned that had to be cleared of all the old cars that was left on it since my uncle passed away and due to her letting Hollywood shoot a movie using her house. Believe it or not it was the house used in the movie Too Wong Fu with Patrick Swayze, Wesley Snipes, Chichi Rodreguez. Anyway before the movie shoot I bought the car for a lousy $40 for a parts car. It had sat for well over 8 years before I bought it and was covered in tree sap etc... It looked rather rough. I got it home and was going to tear into it for parts when I brushed up against it and noticed it really had good white paint under all that crap. I washed it all up and had a friend come over to detail and buff it out and it was in great shape compared to the one that I had already twisted all up due to the rather healthy motor I had in it. Then it became my better street car and ran 12.97's out the gates. I will never part with it due to it's history. Now I have tubbed it all out and waiting on the body work to get finished. It should be a 8 or 9 second car once completed.

The pics shown here are when I first put it together with a lot less parts and only @ 400 HP. This was @ around the time Too Wong Fu was released from from the Movie Theaters. The car has been waiting on the body work to be completed for over three years now. I cannot rush him as he has won Best Body and Paint at one of the SEMA shows. It's in good hands !!! P.S. The 68 Mustang next my Tazmanian Devil was a buddies of mune that I helped work on. It had a 351 Cleveland in it with a 4-speed. Too bad he sold it for $2800 and I could have killed him.

About “The Rumbler”

1996 Mustang GT - 4.6L 2V 215HP/285 RWTQ

 

Specs for “Tazmanian Devil”

Engine -- 355 SB Dart Little M Block that had the decks o-ringed with 686 HP @ 7500 RPM and 531 TQ @ 6000 RPM to the flywheel. Comp Cams .630/.630 solid roller cam, Brodix (first generation) Track 1 heads with 2.08/1.6 hollow stem valves ported, polished, and flowed by FCR Performance at 287.6 cfm IN and 236.3 cfm EX @ .800 lift, Bowtie intake port matched to heads with a Brodix turtle in the plenium , 850 CFM Mighty Demon carb with annular discharge nozzles, Competition Products 1.550 Electro Polished Pro-Alloy valve springs and custom length .080 push rods, a lot of titanium valve train parts, Rocker Shafts, Comp Cams Dry Belt Drive, Crower lightweight Forged Steel crank, Manley Aluminum 6" rods with ARP L-19 Bolts, Milodon complete oiling system, SRP 12.7 to 1 Pistons with file fit rings. All fasteners are ARP studs or bolts.

Ignition -- All ignition is handled via MSD including the Digital 6 ignition box and HPV 1 coil. Wires are MSD 8.5 mm.

Note: There will also be a NOS Cheater system on board as well as I already have it.

Exhaust -- Rare set of Heddman Hustler 3 piece hedders with 1 3/4" primaries and 3" adjustable length collectors. These are no longer made by Heddman. I had them Jet Hot coated. I run them straight into Flow Tech 3" Warlock mufflers.

Trans -- Powerglide with a TCI Pro Tree transbrake, J.W. belhousing and tailshaft, and 5200-5800 TCI Convertor.

Chassis -- Chassis Engineering back half kit with a 12 point roll cage. Sub frame connectors were tied into the front sub frame similar to a full frame car. Stock front end with 5 lug rotors. PST polygraphite bushings.

Rearend -- 9" Ford with all Strange aluminum center section, 1350 Yoke, 5.28 Pro Gears, 35 spline spool, Daytona aluminum pinion support, Moser axles, and Wilwood rear disc brakes. Chassis Engineering ladder bars. I have a set of Art Morrison spring loaded wheelie bars for it too. The driveshaft is a custom aluminum 4" diameter unit.

Rear Tires -- 33" X 19.5" x 15" Micky Thompson Sportsman Pros for the street and 33" x 17" x 15" Goodyear slicks for racing on 15" x 14" Center Line Convo Pros

Front Tires -- 15" x 4" Convo Pros on 24" x 15" x 4" skinnies. Waiting on getting the Wilwood front disc brake conversions until the car is back from the body shop.

Interior -- Custom sheet metal and aluminum floors, RCI red seats with custom Grey cloth seat covers. RCI 5pt harnesses, Interior will be handled in black or grey carpet ( Not there yet) and a custom dash with all Auto Meter gauges. It will have all the safety items for drag racing. Grey ribbon window net. The cage has been painted Pearl Black Cherry but may be changed to Ice Silver.

Exterior -- This will include many body mods like recessed door handles out of a newer Chrysler, hatch tilting to the passenger side, all original glass, custom hood scoop, and all original metal panels with the exception of new rear quarters and a little modifying to the wheel well openings and lip to fit the BIG tires under the car. Paint is to be Chrysler Pearl Black Cherry with custom graphics. All body work is being done at Basik Street Rods and Muscle Cars in Santa Rosa, CA by my brother so some things are even a surprise to me. It will retain a factory rear spoiler. The rear bumper is fiberglass but all remaining panels are factory. We decided to keep the factory glass in it too.

Fuel System -- is all handled with a Magna Fuel Prostar 500 system, regulators, and all hoses are braided with AN fittings. Car has an 8 gallon RCI cell under the rear aluminum bead rolled floor.

Cooling -- handled by a Griffin aluminum radiator 26" x 19" and dual Subaru electric fans. The water pump is a CSI electric pump.

Electrical is handled with two Optima batteries located under the aluminum floor in the hatch. All fuse panels are custom made and use the ATO fuses.

Estimated to run in the mid to low 9's off the spray and very high 8's using a NOS Cheater system. As a factory bodied car it only weighs 2505 without me in it. If I would have kept the fiberglass parts on it it would have weighed around 2250 -2300 lbs. Most of the weight on these cars is in the hatch and doors.

Specs for “The Rumbler”

1996 Ford Mustang GT OEM SPECS

1996 Ford Mustang Performance
4,605 cc 4.6 liters 8 V 90? front longitudinal engine with 90.2 mm bore, 90 mm stroke, 9 compression ratio, light alloy block, light alloy head, double overhead cam, automatic valve adjustment and four valves per cylinder
Unleaded fuel
Fuel economy EPA highway (l/100km): 9
Multi-point injection fuel system
Auxiliary 58 liter fuel tank
Power: 160 kW , 215 HP @ 4,400 rpm; 285 ft lb @ 3,500 rpm

 

Factory Options for “Tazmanian Devil”

This was originally a 4 cyclinder car with a metric 200 automatic trans. Not much there but it was a starting point. 13" wheels and a puny 7.5" ring geared 10 bolt rearend with 2.42 gears. The interior had a floor shifter and bucket seats.

Factory Options for “The Rumbler”

1996 Ford Mustang Handling
ABS
Four disc brakes including four ventilated discs
Rear mechanical limited slip differential
Spacesaver steel rim internal spare wheel
Strut front suspension with stabilizer bar independent with coil springs , multi-link rear suspension with stabilizer bar rigid with coil springs

1996 Ford Mustang Exterior
Front and rear body color impact absorbing bumpers
Driver power black door mirrors , passenger power door mirrors with wide angle
External dimensions: overall length (mm): 4,610, overall width (mm): 1,824, overall height (mm): 1,356, wheelbase (mm): 2,573, front track (mm): 1,524, rear track (mm): 1,491 and curb to curb turning circle (mm): 11,674
Front fog lights
Complex surface lens halogen bulb single headlights
Gloss multi-coat paint , metallic multi-coat paint , black multi-coat paint
Fixed rear window
Trunk/hatch body color wing spoiler
Tinted glass
Weights: curb weight (kg) 1,539
Two-speed windshield wipers with variable intermittent wipe

1996 Ford Mustang Interior
CFC free liquid air conditioning
Fixed mast antenna
Front illuminated ashtray
Stereo audio system with AM/FM
Cargo area light
Cargo capacity: rear seat up; to lower window (liters): 309 and all seats in place (liters): 309
Front seats illuminated cigar lighter
Digital clock
Floor full console with covered storage box
Courtesy lights with two switches
Steering wheel mounted cruise control
Front seats cup holders
Door pockets/bins for driver seat and passenger seat
Floor covering: carpet in passenger compartment and carpet in load area
Carpet floor mats
Driver and passenger front airbag
Sports seat , sports seat
3-point reel front seat belts on driver seat and passenger seat
Front seat center armrest with integral box
Lockable illuminated glove compartment with lid
Height adjustable head restraints on front seats
Illuminated entry system on interior
Internal dimensions: front headroom (mm): 970, rear headroom (mm): 912, front hip room (mm): 1,328, rear hip room (mm): 1,240, front leg room (mm): 1,064, rear leg room (mm): 770, front shoulder room (mm): 1,361, rear shoulder room (mm): 1,323 and interior volume (liters): 2,350
Low fuel level warning
Remote power locks with internal switch
Power steering
Front power windows with door mounted switches and one one-touch
Front reading lights
3-point reel rear seat belts on driver side and passenger side
Split bench symmetrical two rear seats
Rear view mirror
Electric remote trunk/hatch release
Cloth seat upholstery with additional cloth
Seating: four seats
Four speakers
Leather covered steering wheel
Tachometer
Driver and passenger illuminated vanity mirror
Ventilation system with four fan speeds

 

Mods for “Tazmanian Devil”

So many mods since I started but it is now intended for show. This car is still in work at the body shop. I bought all fiberglass body parts for it but once I bought a new chassis (chrome moly) I decided to put all original body parts back this the car.

This car has had two or three different motors in it since I bought it. All being 350 SB Chevies.

Mods for “The Rumbler”

Long Tube Headers, Bassani and Flowmaster Exhaust, Tokica Shocks and Springs, Drilled/Slotted Brakes with Ceramic pads, CAI

 

Photo Albums 1 – 1 of 1

Cover photo of Tazmanian Devil album
Tazmanian Devil
Photos: 21
 

Previous Photo Albums Next Photo Albums

Photo Albums 1 – 1 of 1

Cover photo of 1996 Mustang GT album
1996 Mustang GT
Photos: 3
 

Previous Photo Albums Next Photo Albums

 

Vote This challenge has ended!

Points for Tazmanian Devil Total Votes Points for The Rumbler
79 17 6

 

Comments on this challenge 1 – 9 of 9

Log in to post comments.

Read comments on this challenge (1 – 9 of 9)

Log in to view challenge comments.

Download Drive Magazine Now!

Advertisements

    Special Offers & Deals

Advertisement

 

Cars > Challenges > “Tazmanian Devil” Vs “The Rumbler”

Print your passion at Motortopia.com (http://www.motortopia.com)