How the Modern Racing Pushrod was Invented

February 14th, 2011

Text and Photos by Sam Logan

The most revealing sign of a pushrod’s capability is its resistance to undue deflection—its column stiffness. Until 1993, meaningful research into valve train testing had not been possible. It was only when the Spintron emerged, a revolutionary electrically powered valve train test machine, that profound inadequacies in pushrod design were first revealed.

The Spintron, which incorporates a substitute crankshaft that motors the internal engine components as fast or as long as desired, measures and records valve movement, among other things, by laser tracking. During the initial tests of 1993 the amount of column deflection of the conventional thin-wall 5/16-inch diameter pushrods, and the lofting of the tappets as they became airborne while traveling over the nose of the camshaft lobes, amazed Spintron creator Bob Fox and his collaborator, the late Randy Dorton, tuning wizard at Hendrick Motorsports. In other words, the actual movement of the valve was far removed from that suggested by the camshaft’s lobe profile. As a consequence, pushrod design changed irrevocably.

Fox had established his pushrod company, Trend Performance, in Warren, Michigan, in 1988, after having worked as a tech representative on the phones at nearby Diamond Racing. While at Diamond he became aware of troubling quality issues in pushrod manufacture: Pushrod lengths varied and their ends failed—both ends. Manufacturers would reduce the material thickness of the cup ends in order to form them, and as a consequence, they would crack. Further, their lengths were so inconsistent that each pushrod had to be inspected and graded accordingly. It was this encounter that caused Fox to contemplate life as a pushrod maker.

By the end of his first year in business he had developed two new products, a 5/16-inch pushrod for small-block Chevrolets and a 3/8-inch for big-block Chevrolets. Though they possessed consistency in length and in material thickness at the ends, Fox was unsettled as to what he would do next. Without conclusive data on pushrod operating behavior his future course was unclear.

But by 1993, and aided by extensive data gathered by Spintron testing, he had vastly improved his pushrod product line. Today, nearly two decades later, Trend’s jewel in the crown is their one-piece 7/16-inch double taper creation. Available from 6.000 to 13.000 inches long, and in increments of 0.025-inch, these 4130 chrome molybdenum pushrods are case-hardened to a value of Rockwell Rc60 and used extensively in drag and oval track racing at all levels. Moreover, they’re affordable for all pockets because they’re now made in production quantities and available as shelf-stock items.

To comprehend the advancements made by Trend, it is helpful to recognize and review some fundamentals.

Back to Basics

Pushrods transmit the reciprocating motion of the valve lifters to the rocker arms. Both ends of the pushrod (some have ball-ball ends, some have ball-cup ends) form a connection that accommodates the angular movements of the pushrod from the linear motion of the lifter on one end to the arc motion of the rocker arm on the other.

While transferring the motion created by the cam profile, pushrods are exposed to extreme vibration and shock from the opening and closing of the valve against extreme spring pressure. Certainly, these forces are present in a stock engine, but when the camshaft profile becomes more aggressive, valve spring pressure must also increase if higher peak engine speeds are to be realized. Thus, the strain endured by the pushrod is exponential to the aggressiveness of the cam grind, the weight of the valve, the pressure of the valve spring, and the engine speeds, among other factors.

Inventing a new Pushrod

Trend was the first to recognize that column deflection, harmonics and compression of the pushrod would cause the net valve action to be significantly different from the travel created by the tappet. But these discoveries paled in comparison to tappet lofting. Until 1993 no one had ever heard of lofting, except in golfing circles. No wonder the efforts of so many professional race teams were failing in terms of power production.

Cylinder head designs were improving and advanced machining technologies were paving the way for new, improved cam lobe profiles—profiles that could not have been produced in earlier days. Yet power output was not responding in like fashion. Engine simulation software would show that potential BMEP (brake mean effective cylinder pressure) should have been created, but instead it was being lost.

Prior to the Spintron there was no verifiable method to confirm what design elements of the pushrod were actually required. For proper pushrod design, it is imperative to see in real time what is happening as it is forced to open the valve via all of the intermediate components. To accomplish this, the Spintron employs a high-powered AC electric motor that spins a substitute crankshaft in a test engine. This, in turn, spins the camshaft, which motors the valve train while an advanced laser camera tracks valve motion and pushrod behavior.

Analyzing the Results

Once Fox and his team understood the effect that cam motion had on the conventional 5/16 x 0.080-inch wall pushrod, they knew a stiffer one would be necessary to stabilize the valve train. But it took years before engine builders accepted the heavier pushrod. Now, on reflection, the typical race engine that operated with 5/16 x 0.080-inch wall (55 grams) in 1993 has switched to 7/16-inch double taper with 0.165-inch wall (112 grams) or even 9/16-inch with 0.188-inch wall (160 grams). Quite a switch! The chief threat is no longer weight, but stiffness.

But this isn’t the complete story. After years of exhaustive testing, Fox told Drag Racer magazine that, “The process to create a better pushrod begins not in the machining centers but at the receiving door at the rear of the plant.” He revealed that the key to the success of Trend’s pushrod line is multi-faceted. Every minute detail is critical and includes but is not limited to:

  • Tool steel bars and chrome molybdenum tubing custom-made to Trend’s specifications
  • Materials ordered in large batches of 50,000 to 100,000 feet and each batch checked for specification compliance before pushrod production begins
  • Strict procedures imposed for cutting, forming and machining the steel tubes and bars
  • Heat treatment processes carefully followed

What Happens to the Pushrod When it’s in the Furnace?

Over the years, Trend has acquired an abundance of tribal knowledge, not least in the science of heat-treating. On these issues—of the temperatures and the times observed for quenching and tempering, and of their cryogenic processes—they remain tight-lipped. However, the tooling and fixtures they have devised for heat-treating are clearly visible and intriguing. They have introduced special racks that are made of round bar stainless steel to endure many heating cycles in the furnace without degradation, and the grids of the racks are precisely laid out such that the pushrods are positioned vertically to within 3 degrees.

Before the pushrods are subjected to the heat treatment process they are straight, but as their stresses are relieved during the process, they emerge from heat treatment as warped parts. The problem is that they are not consistently warped; instead each one is warped in its own unique way. Therefore, every single pushrod has to be assessed and straightened. Some are straightened by hand and some of them are straightened by automatic straightening machines that calculate the process by computer analysis. These are sophisticated machines, each costing $200,000.

Probably, the most common material used by Trend today for the manufacture of racing pushrods is 4130 chrome molybdenum tubes. Obviously, these allow the pressurized oil in the lifter bores to be transferred up through the pushrods to the rockers. But for Top Fuel drag cars, Funny Cars and most Alcohol engines, Trend uses solid bar formed from H13 tool steel because the rocker assemblies of those engines are not lubricated via the internals of the pushrods. The reason for switching to this type of tool steel three years ago was because of its inherent toughness and because it responds well to the nitriding process, which invests the pushrods with a very hard wearing surface.

After heat treatment the pushrods are taken to the vibratory tumblers and from there to the inspection room, where the ball ends (formed to plus/minus .001-inch for bind-free operation) and clearance angles and other vital statistics are inspected. Most of the production pushrods are finished in black oxide, while Trend’s custom creations have a polished natural finish. Finally, the pushrods are laser-etched to identify the part and then shipped to the customer.

During Trend’s 20-plus year history, much advancement in pushrod technology has been brought to market. A recent notable example of the firm’s mastery of the racing pushrod is its chrom-moly creation that is fitted with a bronze insert on the cup end. Designed for 500 and 825-ci Pro Stock engines and also large displacement nitrous engines, the bronze insert eliminated damage to the rocker ball that was caused by changes in the constituents of some racing lubricants.

Because the length of the required pushrod isn’t established until the engine is almost completely assembled, it is often the last part ordered, but the part most urgently needed. To overcome this concern, Trend introduced a new quick-ship program called QSP that decrees custom-length pushrods will be shipped within 24 to 48 hours. The service can be applied to any combination of machined tips, tapers or double tapers. Just select the length (from 6.00 to 13.00 inches), the diameter (3/8, 7/16, 9/16-wall thickness) and either a double or single taper, ball-end or radius-cup. This program is further strengthened by an inventory in excess of 100,000 pushrods.

As Bob Fox says, “Telling a racer he can have the part in two weeks is small consolation if he needs it in two days!”

Source

Trend Performance Inc.

Dept. DR

23444 Schoenherr

Warren, MI 48089

586.447.0400

www.trendperform.com (http://www NULL.trendperform NULL.com)

Tags: , , ,

Advertisement

62 Responses to “How the Modern Racing Pushrod was Invented”

  1. overseas adventure travel peru (http://www NULL.facasc NULL.edu NULL.br/nossawiki/index NULL.php?title=Usu%C3%A1rio_Discuss%C3%A3o:HalSumneritlat) says:

    overseas adventure travel peru…

    How the Modern Racing Pushrod was Invented « Drag Racer…

  2. the magic of making up review (http://immm NULL.com/zbxe/index NULL.php?document_srl=126999&mid=board_HSzq01) says:

    the magic of making up review…

    How the Modern Racing Pushrod was Invented « Drag Racer…

  3. natural remedies for depression (http://shurt NULL.tk/naturalremediestokeepdogsaway398762) says:

    natural remedies for depression…

    How the Modern Racing Pushrod was Invented « Drag Racer…

  4. just click the following internet page (http://slnk NULL.info/2hv1t) says:

    just click the following internet page…

    How the Modern Racing Pushrod was Invented « Drag Racer…

  5. nitric max muscle (http://me NULL.9tech NULL.cn/space NULL.php?uid=493869&do=blog&id=44314) says:

    nitric max muscle…

    How the Modern Racing Pushrod was Invented « Drag Racer…

  6. pressandreleases.blogspot.com (http://alturl NULL.com/47ihr) says:

    pressandreleases.blogspot.com…

    How the Modern Racing Pushrod was Invented « Drag Racer…

  7. tumblr.com (http://googleoptimization NULL.tumblr NULL.com/) says:

    tumblr.com…

    How the Modern Racing Pushrod was Invented « Drag Racer…

  8. hay day hack (http://tinyurl NULL.com/OfficialHayDayHackCheatsTool) says:

    hay day hack…

    How the Modern Racing Pushrod was Invented « Drag Racer…

  9. web design lafayette la (http://superfriendlyco NULL.com) says:

    web design lafayette la…

    How the Modern Racing Pushrod was Invented « Drag Racer…

  10. overseas adventure travel greece turkey (http://www NULL.larissawolf NULL.de/2014/03/blogtour-zeitenzauber-gewonnen-hat NULL.html) says:

    overseas adventure travel greece turkey…

    How the Modern Racing Pushrod was Invented « Drag Racer…

  11. Multi Level Marketing (http://blogis NULL.innobasque NULL.com/2009/10/%c2%bfcual-es-el-limite-de-una-empresa-social NULL.html) says:

    Multi Level Marketing…

    How the Modern Racing Pushrod was Invented « Drag Racer…

  12. VItamax Garcinia Cambogia_17627 (http://www NULL.apostille NULL.jp/new/company_03_kr/132034) says:

    VItamax Garcinia Cambogia_17627…

    How the Modern Racing Pushrod was Invented « Drag Racer…

Leave a Comment

You must be logged in to post a comment.