BOOT’s Profile Photo


Havelock, North Carolina
United States

Slinky_Z26’s Profile Photo


Mount Pleasant, Pennsylvania
United States


1981 Pointiac Trans Am


1995 Chevrolet Beretta Z26

“Le' Retta”

Photo of: 1981 Pointiac Trans Am
Photo of: 1995 Chevrolet Beretta

Head to Head


About “Rose”

I bought this about 2 years ago. The interior was shot and the motor was a piece of crap. So I started to slowly piece together the interior. Seats where first, then the dash front and back, then center console, then door panels. After i got the interior done I threw some nice bullet hole rims and fat tires on it.

About “Le' Retta”

This is my first car, its my baby, im near obsessed with making her perfect.


Specs for “Rose”

Engine: 1975 Chevy 383
Dart Iron Eagle heads
1.6 Comp Cams Rocker Arms
7 in. Hardened Steel Push Rods
Hydrolic Flat Tappet Lifters
Mallory Push Rod Guides
Comp Cams Valves
Summit Racing Cam (.442, .442)
Clevit 77 Main, Rod, Cam Bearings
Pontiac 400 Crank
High Volume Oil Pump
K&N Air Filter/Oil Filter
5QT Oil Pan
High Rise Valve Covers (Chrome)
New Water Pump, Fuel Pump, Power Steering Pump, and Alternator
Hurst Shifter Leaver
High Torque Starter
6" Rods
Keith Black Piston Heads 4.030
180 Degree Thermostat
Black Leather Seats (Front and Back)
Black dash (Front and Back)
Black door panels and center console
Panasonic stereo and speakers 4" in the front and 6x9 in the rear.
After Market Gauges
LED Dome and Floorboard lights
Kill Switch
Push button start

Borg Warner Super T10 4 speed manual

Disc all around
drilled and slotted

472 HP- 413HP at the wheel

Specs for “Le' Retta”

3450 S/C engine


Factory Options for “Rose”

No factory options listed.

Factory Options for “Le' Retta”

Power Steering, Tilt Wheel, A/c...


Mods for “Rose”

No modifications listed.

Mods for “Le' Retta”

-Vortech VG-9 S/C With T-Trim Impeller
-WOT-Tech S/C Cam
-9.8:1 Compression
-Fully Balanced Rotating Assembly
-Teflon Coated Performance Wide Cam Bearings
-Clevette 77 Performance Rod Bearings
-Custom Length Pushrods
-Vortech Mondo Bypass Valve
-14psi Billet 7075 Aluminum Pulley
-CompTech Aftercooler
-CXRacing Oversized Heat Exchanger
-Walbro External 255 Fuel Pump
-Holley Hydramat
-60lb Lucas Injectors
-Aeromotive AFPR + SS Braided Lines
-Derale Stacked Plate Motor Oil Cooler + Thermostatic Plate
-SS Braided Fuel Lines
-SS Braided Oil Feed + Oil Return
-SS Braided Brake Booster Line
-SS Braided Coolant Lines
-SS Braided Vacuum Lines
-GM 99" Timing Chain
-Defi Gauges & Tripple Piller Pod
-3400 Block Bored .020 Over
-3400 Forged Diamond Pistons
-3400 Napier Gapless Rings
-350 SBC Forged Scat Rods
-3500 Ported and Polished Upper Intake
-3500 Ported and Polished Lower Intake
-3500 Ported and Polished Heads
-3500 Heads 3 Angle Valve Job + Decked -.010"
-ARP Head Studs
-ARP Rod Bolts
-ARP Crank Dampener Bolt
-ARP Oil Pan Side Bolts
-ARP Torque Converter Bolts
-Comp 26986 Valve Springs
-Manley Lighter Retainers + Keepers
-SI SS Valves
-Upgraded Lifters With LS7 Springs
-Cosmetic MLS Headgaskets
-Fel-Pro Metal Lower Intake Manifold Gaskets
-LX5 65mm Throttle Body
-Amsoil Cold Air Intake
-2 Bar MAP
-180* T-Stat
-Equal Length JETHOT Coated 1 5/8" Primary V6 Headers
-Percys SS Locking Header Bolts
-FULL 2.5" Mandrel SS Exhaust
-Magnaflow XLTurbo Dual Tip Stainless Muffler
-8.5mm MSD Wires
-6061 Aluminum Alternator Pulley
-4 Awg BIG 3 Rewire
-Battery Relocation To Trunk + 2/0ga Wire
-NGK Iridium Plugs 2 Stage Cooler Plugs
-EGR Delete
-ABS Delete
-Dual 1600cfm Permacool 10" Dual Fans
-OBD II Engine Harness Swap


-4000rpm Stall Convertor
-EP Limited Slip Differential
-ZZP Aluminum Transmission Pan
-Hayden Stacked Plate Cooler
-Full Synthetic Fluid
-Full SS AN Cooler Lines
-Alto Eagle Stage 1 Power-pack Benttooth Clutches
-TransGo Shift Kit
-Shimmed Accumulators
-Hardened/Anodized Sannox Valves
-Hardened Sannox Output Shaft
-Hardened Reverse Shell
-Dual Stripe Modulator


-Front Strut Tower Brace
-Rear Shock Tower Brace
-Front 28mm Anti-Sway Bar
-Rear Piggybacked 22mm Solid Z51 Anti-Sway Bar
-Poly Control Arm Bushings
-Poly Filled Trans Mount
-Poly Engine Mount Insert
-Poly 28mm Front Sway Bar Bushings
-Poly 22mm Rear Sway Bar Bushings
-Poly Sway Bar End Links
-Poly Ball-Joint & Tie-Rod Dust Boots
-Billet 7075 Aluminum DogBone & Poly Bushings
-Delrin Inner Tie-Rod Bushings
-4 Wheel Disk Brakes
-4 Wheel Stainless Steel Brake Lines
-Wilwood 4 Piston 12.2" Big Disk Brakes In Front
-Wilwood High Temp Brake Fluid
-Centric Drilled/Slotted Rotors In Back
-Centric Posi-Quiet Ceramic Pads
-KYB GR-2 Struts In Front
-KYB Gas-A-Just In Rear
-Canuck 1.5" Lowering Springs


-Sparco Chrono Road Seats
-Sparco Harnesses
-Sparco Steering Wheel
-17" Motegi DP-10 Rims with 225/45/17 Toyo R888 Tires
-Viper Remote Starter/Alarm System
-Stubby Antenna
-3 Piece CNC Wing
-BMW E-36 Headlights
-HID 6000k Xenon Bulbs
-Clear Turns
-Redline Racing Hood Lifts
-Tinted Tails & Side Markers
-Navigator Fogs
-Custom Kick Panels & Rear Deck
-Billet Aluminum Hurst Shift Handle
-Billet Aluminum E-Brake Handle
-Billet Aluminum MRZ CD Plate
-Custom Billet Fluid Caps
-Stainless Gauge Bezel
-Racing Pedals
-USBody 2" Cowl Induction Hood
-Tint 12% All Around


-Alpine 9886 CD Player
-Alpine Type-R 6"x9" Rear
-Alpine Type-S 6.5" Front
-Alpine KTP-445 Amp


Photo Albums 1 – 1 of 1

Cover photo of Rose album
Photos: 5

Previous Photo Albums Next Photo Albums

Photo Albums 1 – 1 of 1

Cover photo of Engine album
Photos: 2

Previous Photo Albums Next Photo Albums


Vote This challenge has ended!

Points for Rose Total Votes Points for Le' Retta
11 3 4


Comments on this challenge

Log in to post comments.

Read comments on this challenge

Log in to view challenge comments.